Orchid Technology
                       SoundWave32 Series
                Installation with OS/2 Warp v3.0
                --------------------------------


This document gives detailed instructions for using the Business 
Audio driver that comes with OS/2 Warp with the Orchid SoundWave 
32, and SoundWave 32+SCSI.  This will allow WAV playback and 
record capability, but not the use of MIDI or SoundBlaster 
support under OS/2.  At this time there are no plans for further
OS/2 development for the SoundWave 32 series.

These instructions assume that you already have Warp installed on 
your system.  During the course of the Business Audio driver 
installation OS/2 will need to read files from your OS/2 CD-ROM 
or OS/2 diskettes, so have those handy before beginning the 
installation.


Installation Instructions
-------------------------
1.  Before beginning the OS/2 installation, run Windows from DOS 
    and check the driver setup for the SoundWave 32 in the 
    Drivers section of Control Panel.  Look at the "Setup" button 
    screen for the SW32 driver and write down the addresses 
    you've selected for use for the Windows Sound System 
    emulation.  You'll need to know those addresses during the 
    OS/2 install.

2.  After making note of the addresses, close Windows and boot
    Warp.

3.  Once Warp is up and running, open the OS/2 System Folder on 
    the desktop.  Open the System Setup folder, then choose the 
    Selective Install icon.  

4.  From the System Configuration screen look at the Multimedia 
    Device Support selection.  That choice should say "None".  If 
    that line indicates that you already have a Multimedia driver 
    installed (other than Business Audio) you should remove it 
    and restart OS/2 before proceeding.  If the selection says 
    "None", then click on the Multimedia Device Support button.

5.  On the Device Selections and Settings screen you'll see 2 
    columns.  One called Supported Device(s), and another called 
    Devices(s) in System to be Installed.  From the Supported 
    Devices column, highlight the "Business Audio (AD1848)" 
    choice, and press the Add button.  The Business Audio 
    (AD1848)" choice should now show in the Devices(s) in System 
    to be Installed column.  

6.  **IMPORTANT NOTE**  This step is often missed and is very 
    important in order for the driver to work correctly.  Press 
    the Device Settings button and set the Port Address, DMA and 
    Interrupt Level values to match the addresses you made note 
    of in step 1 (the addresses you use for the SW32 for Windows 
    Sound System).  After entering the addresses, press the OK 
    button.

7.  From the Device Selections and Settings screen, press OK 
    again.  Then from the System Configuration screen, press OK 
    again.  

8.  The OS/2 Setup and Installation screen will pop up, with the 
    Multimedia checkbox checked.  Press the Install button (don't 
    make any changes on that screen).

9.  OS/2 will ask you for the path to your OS/2 CD-ROM, or prompt 
    you to insert some OS/2 diskettes.  Check that the path is 
    correct, and insert the disks as instructed.

***** NOTE:  DO NOT SHUTDOWN OR RESTART OS/2 AT THIS TIME.

10. Even though OS/2 will notify you that you should restart your 
    system, you need to edit some lines in your CONFIG.SYS file 
    first.  Use your favorite text editor to change the following
    line:

    DEVICE=C:\MMOS2\BUSAUDIO.SYS T:MS_SOUND ... etc.

          to read.....

    DEVICE=C:\MMOS2\BUSAUDIO.SYS T:SW32 ...  etc.  
                       
    The completed line should look something like this.  Your 
    address values may vary:

     DEVICE=C:\MMOS2\BUSAUDIO.SYS T:SW32 P:530 D:3 I:11 N:BSAUD1$

11. Save your changes to CONFIG.SYS, then Shutdown and restart 
    OS/2 for the changes to take effect.  Once OS/2 restarts you 
    should have the ability to record and playback WAV files.  



Other Orchid Multimedia Products with OS/2
------------------------------------------
This document only covers installation of the Business Audio 
driver for OS/2 Warp with the SoundWave 32 Series.  There is also 
a Warp driver for the Orchid CDS-3110 CD-ROM drive.  You can 
download the file CDD110.ZIP from the BETA library of the Orchid 
Bulletin Board (510)683-0327, or from the OS2USER forum on 
CompuServe (GO OS2USER, Library 3 OS2HARDWARE).  CDD110.ZIP will 
work for either OS/2 v2.1x or OS/2 Warp v3.0.  


Technical Support  
-----------------
Telephone support is available Monday through Friday from 7 a.m. 
to 5 p.m. PST at (510)661-3000.  Additional software drivers and 
upgrades are available through Orchid's 24-hour Bulletin Board 
Service (510)683-0327 (14.4K baud, 8N1).  Access Orchid support 
via our CompuServe forum.  Enter GO ORCHID at any ! prompt to 
enter the Orchid section of the Multimedia B Vendor Forum.


Orchid Technology                  Orchid Technology        
Technical Support                  Headquarters
232 East Warren Avenue             45365 Northport Loop West
Fremont, CA 94539-7085             Fremont, CA 94538
(510)661-3000                      (510)683-0300


Orchid France S.A.R.L.   Orchid Technology GmbH   Orchid (Europe) Ltd.
Colombes, France         Meerbusch, Germany       Basingstoke, UK
Tel:(33)-1-47 80 70 50   Tel:49 2132 80071        Tel: 256-479898

-- documentation revised 08/95  Orchid Technology Technical Support